2.7. Allocating Disk Space

There are three ways to allocate disk space for FreeBSD. Guided partitioning automatically sets up disk partitions, while Manual partitioning allows advanced users to create customized partitions. Finally, there's the option of starting a shell where command-line programs like gpart(8), fdisk(8), and bsdlabel(8) can be used directly.

Figure 2.10. Selecting Guided or Manual Partitioning
Selecting Guided or Manual Partitioning

2.7.1. Guided Partitioning

If multiple disks are connected, choose the one where FreeBSD is to be installed.

Figure 2.11. Selecting from Multiple Disks
Selecting from Multiple Disks

The entire disk can be allocated to FreeBSD, or just a portion of it. If [ Entire Disk ] is chosen, a general partition layout filling the whole disk is created. Selecting [ Partition ] creates a partition layout in unused space on the disk.

Figure 2.12. Selecting Entire Disk or Partition
Selecting Entire Disk or Partition

After the partition layout has been created, review it carefully for accuracy. If a mistake has been made, selecting [ Revert ] will reset the partitions as they were previously, or [ Auto ] will recreate the automatic FreeBSD partitions. Partitions can be manually created, modified, or deleted. When the partitioning is correct, select [ Finish ] to continue with the installation.

Figure 2.13. Review Created Partitions
Review Created Partitions

2.7.2. Manual Partitioning

Manual partitioning goes straight to the partition editor.

Figure 2.14. Manually Create Partitions
Manually Create Partitions

Highlighting a drive (ada0 in this example) and selecting [ Create ] displays a menu for choosing the type of partitioning scheme.

Figure 2.15. Manually Create Partitions
Manually Create Partitions

GPT partitioning is usually the most appropriate choice for PC-compatible computers. Older PC operating systems that are not compatible with GPT may require MBR partitioning instead. The other partitioning schemes are generally used for uncommon or older computer systems.

Table 2.1. Partitioning Schemes
AbbreviationDescription
APMApple Partition Map, used by PowerPC® Macintosh®.
BSDBSD Labels without an MBR, sometimes called dangerously dedicated mode. See bsdlabel(8).
GPTGUID Partition Table.
MBRMaster Boot Record.
PC98MBR variant, used by NEC PC-98 computers.
VTOC8Volume Table Of Contents, used by Sun SPARC64 and UltraSPARC computers.

After the partitioning scheme has been selected and created, selecting [ Create ] again will create new partitions.

Figure 2.16. Manually Create Partitions
Manually Create Partitions

A standard FreeBSD GPT installation uses at least three partitions:

Standard FreeBSD GPT Partitions
  • freebsd-boot - FreeBSD boot code.

  • freebsd-ufs - A FreeBSD UFS filesystem.

  • freebsd-swap - FreeBSD swap space.

Another partition type worth noting is freebsd-zfs, used for partitions that will contain a FreeBSD ZFS filesystem. See Section 20.2, “The Z File System (ZFS)”. gpart(8) shows more of the available GPT partition types.

Multiple filesystem partitions can be used, and some people may prefer a traditional layout with separate partitions for the /, /var, /tmp, and /usr filesystems. See Example 2.3, “Creating Traditional Split Filesystem Partitions” for an example.

Size may be entered with common abbreviations: K for kilobytes, M for megabytes, or G for gigabytes.

Tip:

Proper sector alignment provides the best performance, and making partition sizes even multiples of 4K bytes helps to ensure alignment on drives with either 512-byte or 4K-byte sectors. Generally, using partition sizes that are even multiples of 1M or 1G is the easiest way to make sure every partition starts at an even multiple of 4K. One exception: at present, the freebsd-boot partition should be no larger than 512K due to boot code limitations.

A mountpoint is needed if this partition will contain a filesystem. If only a single UFS partition will be created, the mountpoint should be /.

A label is also requested. A label is a name by which this partition will be known. Drive names or numbers can change if the drive is connected to a different controller or port, but the partition label does not change. Referring to labels instead of drive names and partition numbers in files like /etc/fstab makes the system more tolerant of changing hardware. GPT labels appear in /dev/gpt/ when a disk is attached. Other partitioning schemes have different label capabilities, and their labels appear in different directories in /dev/.

Tip:

Use a unique label on every filesystem to avoid conflicts from identical labels. A few letters from the computer's name, use, or location can be added to the label. For instance, labroot or rootfs-lab for the UFS root partition on the lab's computer.

Example 2.3. Creating Traditional Split Filesystem Partitions

For a traditional partition layout where the /, /var, /tmp, and /usr directories are separate filesystems on their own partitions, create a GPT partitioning scheme, then create the partitions as shown. Partition sizes shown are typical for a 20G target disk. If more space is available on the target disk, larger swap or /var partitions may be useful. Labels shown here are prefixed with ex for example, but readers should use other unique label values as described above.

By default, FreeBSD's gptboot expects the first UFS partition found to be the / partition.

Partition TypeSizeMountpointLabel
freebsd-boot512K  
freebsd-ufs2G/exrootfs
freebsd-swap4G exswap
freebsd-ufs2G/varexvarfs
freebsd-ufs1G/tmpextmpfs
freebsd-ufsaccept the default (remainder of the disk)/usrexusrfs

After the custom partitions have been created, select [ Finish ] to continue with the installation.

All FreeBSD documents are available for download at http://ftp.FreeBSD.org/pub/FreeBSD/doc/

Questions that are not answered by the documentation may be sent to <freebsd-questions@FreeBSD.org>.
Send questions about this document to <freebsd-doc@FreeBSD.org>.